CMPHYP=DISABLED, INMUX=DIRECT, NWPUEN=DISABLED, RIEN=DISABLED, FIEN=DISABLED, PMUX=CMPNP0, INVEN=DISABLED, CMPHYN=DISABLED, NMUX=CMPNN0, CMPMD=MODE0, PWPUEN=DISABLED
Input and Module Mode
| NMUX | Negative Input Select. 0 (CMPNN0): Select CMPnN.0 (PB0.1). 1 (CMPNN1): Select CMPnN.1 (PB0.2). 2 (CMPNN2): Select CMPnN.2 (RESERVED). 3 (CMPNN3): Select CMPnN.3 (RESERVED). 4 (CMPNN4): Select CMPnN.4 (PB2.1). 5 (CMPNN5): Select CMPnN.5 (PB2.5). 6 (CMPNN6): Select CMPnN.6 (RESERVED). 7 (CMPNN7): Select CMPnN.7 (PB3.0). 8 (CMPNN8): Select CMPnN.8 (VREF Pin). 9 (CMPNN9): Select CMPnN.9 (VBAT). 10 (CMPNN10): Select CMPnN.10 (VDC). 11 (CMPNN11): Select CMPnN.11 (Digital LDO Output). 12 (CMPNN12): Select CMPnN.12 (Memory LDO Output). 13 (CMPNN13): Select CMPnN.13 (Analog LDO Output). 14 (CMPNN14): Select CMPnN.14 (VIO). 15 (CMPNN15): Select CMPnN.15 (RESERVED). |
| PMUX | Positive Input Select. 0 (CMPNP0): Select CMPnP.0 (PB0.0). 1 (CMPNP1): Select CMPnP.1 (PB0.3). 2 (CMPNP2): Select CMPnP.2 (RESERVED). 3 (CMPNP3): Select CMPnP.3 (RESERVED). 4 (CMPNP4): Select CMPnP.4 (PB2.0). 5 (CMPNP5): Select CMPnP.5 (PB2.4). 6 (CMPNP6): Select CMPnP.6 (RESERVED). 7 (CMPNP7): Select CMPnP.7 (RESERVED). 8 (CMPNP8): Select CMPnP.8 (VREF Pin). 9 (CMPNP9): Select CMPnP.9 (RESERVED). 10 (CMPNP10): Select CMPnP.10 (Temperature Sensor Output). 11 (CMPNP11): Select CMPnP.11 (Charge Pump / 2). 12 (CMPNP12): Select CMPnP.12 (Digital LDO Output). 13 (CMPNP13): Select CMPnP.13 (Memory LDO Output). 14 (CMPNP14): Select CMPnP.14 (Analog LDO Output). 15 (CMPNP15): Select CMPnP.15 (RESERVED). |
| INMUX | Input MUX Select. 0 (DIRECT): Connects the NMUX signal to CMP- and the PMUX signal to CMP+. 1 (CMPP_VSS): Connects VSS to CMP- and the PMUX signal to CMP+. 2 (CMPP_DAC): Connects the NMUX signal to CMP-, the PMUX signal to the Comparator DAC voltage reference, and the DAC output to CMP+. 3 (CMPN_DAC): Connects the PMUX signal to CMP+, the NMUX signal to the Comparator DAC voltage reference, and the DAC output to CMP-. |
| CMPMD | Comparator Mode. 0 (MODE0): Mode 0 (fastest response time, highest power consumption). 1 (MODE1): Mode 1. 2 (MODE2): Mode 2. 3 (MODE3): Mode 3 (slowest response time, lowest power consumption). |
| FIEN | Falling Edge Interrupt Enable. 0 (DISABLED): Disable the comparator falling edge interrupt. 1 (ENABLED): Enable the comparator falling edge interrupt. |
| RIEN | Rising Edge Interrupt Enable. 0 (DISABLED): Disable the comparator rising edge interrupt. 1 (ENABLED): Enable the comparator rising edge interrupt. |
| DACLVL | Comparator DAC Output Level. |
| NWPUEN | Negative Input Weak Pullup Enable. 0 (DISABLED): Disable the negative input weak pull up. 1 (ENABLED): Enable the negative input weak pull up. |
| PWPUEN | Positive Input Weak Pullup Enable. 0 (DISABLED): Disable the positive input weak pull up. 1 (ENABLED): Enable the positive input weak pull up. |
| CMPHYN | Negative Hysteresis Control. 0 (DISABLED): Disable negative hysteresis. 1 (NEG_5_MV): Set negative hysteresis to 5 mV. 2 (NEG_10_MV): Set negative hysteresis to 10 mV. 3 (NEG_20_MV): Set negative hysteresis to 20 mV. |
| CMPHYP | Positive Hysteresis Control. 0 (DISABLED): Disable positive hysteresis. 1 (POS_5_MV): Set positive hysteresis to 5 mV. 2 (POS_10_MV): Set positive hysteresis to 10 mV. 3 (POS_20_MV): Set positive hysteresis to 20 mV. |
| INVEN | Invert Comparator Output Enable. 0 (DISABLED): Do not invert the comparator output. 1 (ENABLED): Invert the comparator output. |